Products

This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o'ring and put it on the new adapter. Features: 6061 aluminum T6 Black anodized Knurled thread protector

  This design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included. Factory gun already includes the bushing. The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun. I would recommend going with minimum the .357 Ronin for this gun. The .357 FX suppressor is not enough to quiet this gun down. IF you use an Emperor with this gun, do not add the extender. Too much weight added applied to the adapter and may cause inaccuracies.  Made by CNC for accuracy Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud. Matte Black anodize Knurled thread protector When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.

*Note: For the Akela, remove one of the factory baffles in order for the adapter to fit flush. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers

Features: This adapter has a 1/2 x 20 adapter at the end Has two holes on top like OEM so you can use original screws and front site. Overall length from one end to the other is 3.12 inches has groove underneath just like OEM for ease of removing fill cap CNC Matte Black Anodize Match this up with a .22 Tatsu and you have a nice quiet gun.

Want to make your Prod quieter? You'll need this 1/2 x 20 adapter, it will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.  The Sumo 1/2 x 20 is my favorite suppressor for this gun. However, in order to fill this gun with the Sumo, you'll have to remove the suppressor. An alternative is to go with either the Tanto or KOI with cone rear cap. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

This adapter extends the shroud 1.5 inches or about 38.1mm. Pair it up with a .22-25 Tanto 1/2 x 20 Bolt #S69 and this pistol will be very quiet. No need to remove the suppressor to fill the gun. Features: 6061 Aluminum Black anodized Comes with knurled thread protector  

Marauders are great entry level PCP guns. There are lots of mods you can do to make them more powerful. More power means a louder gun. To make it backyard friendly, make sure to grab this adapter to allow you to screw on an aftermarket LDC. Threaded end that goes into the OEM shroud is 13/16 - 28. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Want to make your Compatto quieter? You'll need this 1/2 x 20 adapter that will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.  Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

This slide on adapter will fit the Bushbuck up to .45 cal. I would recommend the .45/50 Emperor v3 along with the 6.5 inch extender to tame this beast!

This is a slide on adapter for the Crosman 2240, ID measures 7/16.

This adapter converts the factory shroud threads from M20x1 to 1/2 x 20. Features: Aluminum 6061 T6 Black anodize Comes with knurled thread protector

You'll need this 1/2 x 20 adapter if you can't get the OEM adapter off the airstream that came with the gun.   Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers Remove factory suppressor and screw this into the shroud directly onto the barrel.

Features: Material is 6061 T6 Aluminum Black anodize Comes with knurled thread protector

This kit is to replace the stock factory shroud and allows you to screw on an airgun suppressor with 1/2 x 20 threads. The shroud is 2 inch in diameter so best to use Ronin/Emperor/Fatboy with it.  Things to keep in mind:  Mechanical noise will still be loud. Nothing we can do to reduce that with our kit. Have someone shoot the gun and take about 10 steps back. You'll get a better feel for the muzzle noise. The shroud is empty to provide the max air expansion. The stock will fold but will not lock. you will need to get the extended pin from Edgun West Available in two sizes 250mm and 350mm It's ok to use the 350mm shroud on a 250mm barrel (more volume = quieter) Features: Made of 6061 T6 Aluminum Black anodized 1/2 x 20 male threads (does not have a thread protector) Comes with 2 Stainless Steel screws  Instructions

The Edgun Matador R3M is one of the most accurate bullpups on the market. Like any gun, the shroud could be improved. This baffle unit replaces the OEM baffles.  Unscrew the factory unit and screw on this one the same way. It was important to keep the rear bolt to help tension the barrel. I've added more vent holes in the rear to allow more air to flow to the rear of the shroud. At the tip of the unit there is now a built in 1/2 x 20 adapter with a knurled thread protector.  Features: Made of steel for durabilityCompatible with .22 and .25fits Standard, Compact and Long MatadorsCNC machinedComes with Knurled capIncludes O-ring

Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model.

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .22 to .30 cal. JTS Airguns .22 to .25 cal.