Lil Foot 2.0 Compressor M69
Lil Foot 2.0 Compressor M69 $ 10,500.00
New portable compressor by PCP Kong. This little workhorse has abuilt-in power adapter so you can plug directly into your 110v walloutlet or 12v car battery. Features:- LED Digital Display- 4500 PSI/310 BAR- Adjustable pressure setting- comes with an extended fill probe- comes with a carry bag- Compatible with 110v wall outlet- 12v car battery or standalone 12v supply- Auto shutoff- Fan cooled- 18 lbs- 11”L x 9”H x 8.5”W- Uses 100% silicone oil only (please see manual)- 1-year limited warranty- Will not fill a scuba tank*Comes with silicone oil
RYU Spare Baffles
RYU Spare Baffles $ 662.00
Customize the size of your RYU or replace sections of your unit with these individual parts. Please note I would not add more than 2 extra baffles on top of the factory units. If you plan to do so, I would recommend going one caliber size up. *The products on DonnyFL are INTENDED for use on airguns only.  It is a violation of Federal law to use this product in a manner inconsistent with what it was intended for.
Quick release muzzle brake - M84
Quick release muzzle brake ... $ 2,204.00
This muzzle brake or air stripper attaches to the front of any air rifle equipped with a DonnyFL Quick Disconnect Adapter. Features: Made of aluminum 6061 T6 Black anodize Weights 2.9 oz Comes with M58 Air Stripper Insert Kit.
Quick Disconnect End Caps
Quick Disconnect End Caps $ 1,102.00
If you own a Sumo, Tatsu, Ronin, Shogun, Tanto, Emperor or FX DonnyFl moderator and want to convert it to a QD. This conversion kit will allow you to do so.  Features: Indexed so it locks on at same position every time Made of 7075 aluminum Grey anodized Includes barrel/shroud adapter and rear cap Select the barrel thread specific to your airgun
Replacement felt and O-rings for Sumo, Ronin and Shogun
Replacement felt and O-ring... $ 287.00
This package comes with 4 replacement felt wraps, screen and o-rings for the selected moderator model.
Taipan Mutant Speed Dialer M11
Taipan Mutant Speed Dialer M11 $ 1,102.00
Look ma no more tools! You no longer need the prongs or hex key whenever you want to adjust your spring tension. Loosen the side thumb screw allowing you to adjust the HST in or out with ease. Once you're done, tighten back the side screw.  Features: CNC parts Red anodize to add character to your gun Package includes side thumb screw and HST adjuster
Taipan Veteran Speed Dialer M12
Taipan Veteran Speed Dialer... $ 1,102.00
Look ma no tools! You don't need the prongs or hex key whenever you want to adjust your spring tension. Loosen the side thumb screw to adjust the HST in or out with ease. Once you're done, tighten back the side screw.  Features: CNC parts Has a through hole in the back in case the spring tension is too much, you can use a hex key or thin screw driver to help turn Black anodize to add character to your gun Package includes side thumb screw and HST adjuster
Modified Cricket Side Plate M10
Modified Cricket Side Plate... $ 441.00
One of the downside to the Crickets that you hear all the time is how cumbersome it is to switch magaizines. Most of the time you need two hands to complete a simple task. This modified side plate allows you to do just that, pull back the indexer and rest it in the second slot. Once the magazine has been inserted, lift up the indexer lever and return it to the front. *Not compatible with .357 Cricket or Cricket II Please note* Do not tighten the right screw too tight. This will lock the index arm. See pictures. Install tips: http://www.talonairgun.com/forum/viewtopic.php?f=33&t=37048&start=20
KOI/Tanto Endcaps
KOI/Tanto Endcaps $ 772.00
Get additional end caps to use with your KOI and Tanto.   
Umarex Gauntlet Aluminum Air Stripper M5
Umarex Gauntlet Aluminum Ai... $ 251.00
This piece replaces the OEM plastic air stripper. This will help in the long run as the plastic ones tend to crack. It includes o-ring. Features: 6061 Aluminum Matte black anodize Other things to consider: Gauntlet 1/2 x 20 adapter Gauntlet short shroud with 1/2 x 20 adapter **NOT COMPATIBLE WITH THE .30 CAL GAUNTLET 2
Umarex Gauntlet Short Shroud with 1/2 x 20 Adapter M14
Umarex Gauntlet Short Shrou... $ 1,253.00
This shroud is 3 inches shorter than OEM. I removed the plastic baffle that came with the gun and added a 1/2 x 20 adapter. This allows you to put a bigger suppressor in the front and make this gun super quiet. I highly recommend the Tatsu. All you will hear is the hammer spring. Overall length is 23 inches. You will need the OEM spring.  Features: 23 inches overall CNC Matte black anodize Other things to consider: Gauntlet Aluminum Air Stripper Directions:1. Remove the factory shroud by turning the shroud counter clockwise2. You won't need the factory black baffle but hang on to the spring3. Remove factory air stripper by pulling it off4. Put the o'ring onto the DonnyFL air stripper5. Slide the air stripper onto the barrel6. Take the short shroud and drop the factory spring down the shroud towards the side that has the adapter7. Apply some silicone grease onto the air stripper o'ring8. Slide short shroud over the barrel, once you're at threaded part in the rear, turn clockwise to tighten.To install a suppressor, remove the thread protector from the shroud. Screw on the suppressor. ​Very important that you include the factory spring, it holds the air stripper in place. Without it, the stripper will fall off and block the exit hole. *Return Policy    **NOT COMPATIBLE WITH THE .30 CAL GAUNTLET 2
Extended Quick Disconnect 1/8 BSP M20
Extended Quick Disconnect 1... $ 441.00
This extended quick disconnect (QD) makes it easy for those guns with hard to reach fill nipples. A must have for FX Impacts. 1/8 BSP male threads Max 5000 psi (Do not exceed recommended pressure) Release collar close to 1.20 inches long Comes with sealed washer  
Sumo/Tatsu/Shogun Endcaps
Sumo/Tatsu/Shogun Endcaps $ 772.00
Interchangeable rear endcaps for the latest model of Sumo, Tatsu and Shogun. Works with models with the grooves in the front cap.
Emperor/Ronin v3 6.26 inch Extender/Extension
Emperor/Ronin v3 6.26 inch ... $ 1,323.00
Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model.
Ronin/Emperor Endcaps
Ronin/Emperor Endcaps $ 772.00
Interchangeable rear endcaps for the latest model of Ronin and Emperor. Works with models with the grooves in the front cap.
FX Wildcat Mag Holder M27
FX Wildcat Mag Holder M27 $ 522.00
With Matt247365 from Airgun Nation's blessing, I am happy to offer these easy to install Wildcat mag holders. Compatible with .177  .22  .25 and .30 caliber. Your magazine clicks securely into the Mag holder using it’s own ball bearing and can rotate for easy loading with one hand while on the gun. As many as 4 Magholders can fit on the Wildcat at one time. You can mount 1, 2, 3 or 4 in a variety of configurations facing either to the front or to the rear and on either side or on both sides. Features: Made of 6061 T6 aluminum black anodize CNC machined Uses 2.5 mm Hex key
Quick Disconnect Fill Probes
Quick Disconnect Fill Probes $ 522.00
No adapters needed, just put this in your quick disconnect coupling and you're all set. *You're purchasing one item, not all are included in the price. Made of stainless steel and available for: EDgunsVulcanWeihrauchTaipanFX WildcatKalibrgun CricketHatsan
Stainless Steel Extended Quick Disconnect w/ Foster Fitting M32
Stainless Steel Extended Qu... $ 551.00
This extended quick disconnect (QD) makes it easy for those guns with hard to reach fill nipples. A must have for FX Impacts. Male foster fitting Max 4500 psi (Do not exceed recommended pressure) Release collar close to 1.20 inches long  
Suppressor Tubes
Suppressor Tubes $ 42.00
Protective case for your DonnyFL suppressors. Made of hard cardboard with an anti-scratch outer surface. Please note, when you order a new moderator going forward. These are included.  
Edgun R3M and R3 Degasser Tool M39
Edgun R3M and R3 Degasser T... $ 992.00
This tool makes degassing the Edgun R3M and R3 safe and easy. It also acan also be used to pull out the regulator. Instructions: before screwing the tool onto the Edgun, back out the screw a little to allow the valve pin to go into the tool.  screw the tool onto the valve Using the blue knob slowly screw into valve pin. You'll start to hear a hissing noise and that's the air being released.  once empty, your gauge should be down to zero to remove the regulator, make sure the gun is completely empty. Unscrew the screws holding the regulator in place. Once all the screws are out, screw the degasser tool onto the valve and pull it out of the air tube