Products

Made of steel 1/2 x 20 UNF threads compatible with .22 and .25 caliber Comes with black anodized Aluminum thread protector Tight fit and has two set screws (M4) to help secure it onto the barrel Uses 2mm hex keys for set screws

Add a moderator to this adapter to make the Condor SS super quiet.  Features:  Compatible with .177 to .25 Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip Comes with Oring

Add a moderator to this adapter to make the Talon SS and TalonP super quiet.  Features:  Compatible with .177 to .25 Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip Comes with Oring

If your TalonP Carbine came with a factory moderator and you need it to be more quiet, install this adapter. It'll then allow you to screw on a suppressor that is threaded 1/2 x 20. Features:  Compatible with .177 to .25 Made by CNC for accuracy Material is 6061 T6 Aluminum Black matte anodize Diamond pattern knurling for easy grip

Note: Please measure your barrels outer diameter before ordering. Compare with the sizes below. There maybe a change in their barrel anodizing which is causing the OD to be a little larger. Features: Made of steel  M18x1 threads compatible with .357 Ronin or Emperor with M18x1 endcap Comes with black anodized Aluminum thread protector Adapters are tight fit and have two set screws (M4) to help secure to the barrel Very tight fit, may require some sanding inside the adapter Uses 2mm hex keys for set screws I would recommend putting a thin film of blue loctite on the barrel then slide on the adapter. Let it set overnight. The following are the inner diameter for my adapters: .257 = Use Condor adapter here .308/357 = 16mm or .625 inches "A34" .308/.357 = 17mm or .67inches "A95" .457 = .707 to .71 inches Two sizes for .50 (please use a caliper and measure your barrel's outer diameter) .50 =  18.83 mm .50 = 19.1 mm  

This adapter screws directly to the end of the factory Texan LSS shroud. It has M18x1 male threads to pair with my big bore suppressors. Add an Emperor or Ronin to tame the beast!  Features: 6061 Aluminum Matte black anodize knurled thread protector

Features: Compatible with .177, .22 and .25 6061 Aluminum T6 Black anodized Knurled cap 1/2 x 20 male threads

What's even better than a fun gun? A quiet one! Stainless steel adapter now allows you to put on more effective after market suppressors. There's a through hole in the threads to help tighten it onto the gun or assist to remove. I've seen some scratched up guns where people slipped with a prong trying to tighten or remove.  Features Made by CNC for accuracy Stainless Steel Black anodized diamond pattern knurling thread protector

This adapter screws into the OEM shroud allowing you to screw a suppressor with 1/2 x 20 UNF of your choice. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Includes thread protector Compatible up to .30 cal

This adapter screws into the OEM shroud allowing you to screw on either the Emperor or .357 Ronin. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip M18x1 threads

This adapter replaces the PP750 factory front cap. Has 1/2 x 20 threads to screw on an airgun suppressor. Features: 6061 Aluminum CNC machined Matte black finished

This beautiful pistol has a little bark to it. Add this adapter to it and your favorite suppressor to make it more enjoyable . Features: through hole in 1/2 x 20 threads for easy tightening or removal hole on side of adapter in case adapter is stuck in suppressor knurled cap CNC Matte black anodize

There are two options for the BP17 Option 1: If you would like to keep the factory shroud and add a suppressor to the end of it get #A49 Option 2: If you would like to remove the factory shroud and keep the gun as short as possible with a suppressor, select #A74. This is the version Ted did a review on.

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .357 model

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .22 and .25 calibers

This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o'ring and put it on the new adapter. Features: 6061 aluminum T6 Black anodized Knurled thread protector

  This design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included. Factory gun already includes the bushing. The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun. I would recommend going with minimum the .357 Ronin for this gun. The .357 FX suppressor is not enough to quiet this gun down. IF you use an Emperor with this gun, do not add the extender. Too much weight added applied to the adapter and may cause inaccuracies.  Made by CNC for accuracy Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud. Matte Black anodize Knurled thread protector When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.

*Note: For the Akela, remove one of the factory baffles in order for the adapter to fit flush. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers

Features: This adapter has a 1/2 x 20 adapter at the end Has two holes on top like OEM so you can use original screws and front site. Overall length from one end to the other is 3.12 inches has groove underneath just like OEM for ease of removing fill cap CNC Matte Black Anodize Match this up with a .22 Tatsu and you have a nice quiet gun.

Want to make your Prod quieter? You'll need this 1/2 x 20 adapter, it will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.  The Sumo 1/2 x 20 is my favorite suppressor for this gun. However, in order to fill this gun with the Sumo, you'll have to remove the suppressor. An alternative is to go with either the Tanto or KOI with cone rear cap. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip