Products

Get additional end caps to use with your KOI and Tanto.   

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers

This adapter is compatible with the K300 model. Adds 1/2 x 20 male threads to the end of your airgun. Features: 6061 aluminum T6 black anodized Includes knurled thread protector  

Please Read*  If you remove your factory moderator and the threads look like exhibit B, select the .30 specific adapter A110. To pick the correct adapter, you will need to measure the length of your carbon fiber shroud. If your shroud measures 13 or 17 inches, you'll need A57. If your shroud measures 11.5 inches and you eventually want to use a longer bottle(580 cc) you'll need A72 If  your shroud is 11.5 inches long and you have no intentions of adding a longer bottle then go with A73 Easy to install 1/2 x 20 adapter for the LCS SK19. Convert your shroud to accept any 1/2 x 20 suppressor of your choice. I would highly recommend a Ronin one size up from what the gun's caliber is. Still very effective but more importantly reduces the chance of pellet clipping, especially during rapid fire. *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping. CNC Matte Black Anodize Compatible with .22/25 caliber

Right handed threads to convert barrels with M14x1 to 1/2 x 20. Features: 16.05mm OD, 15.20mm deep on female side Black anodized and knurled throughout on the outside.

This adapter is about 22mm OD x 38.30mm Length. It converts barrel threads from M14x1.25 to 1/2 x 20.  Does not come with a thread protector.  Features: 6061 T6 Aluminum Silver (no anodize)

Upgrade kit for your fatboy muzzle brake. Comes with two air strippers for each size.  Note* Not compatible with the gold limited edition muzzle brakes. Features: .177/22, .22/25 and .25/30 Bronze anodize Delrin tool to install air strippers

This adapter will allow you to screw on a 1/2 x 20 airgun suppressor. Features: Knurled cap CNC Matte black anodize *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.

Nice addition to quiet down a nice entry level PCP bullpup, add any 1/2x20 suppressor of your choice.  *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodized diamond pattern knurling thread protector Compatible with .22 and .25 calibers New model allows you to screw on larger diameter suppressors like the Sumo and Ronin without interfering with the fill probe

This is only for the barrel adapter. Moderator rear cap not included. Features: 7075 Aluminum Anodized 1/2 x 20, M14x1.25 will include set screw and wrench

If you own a Sumo, Tatsu, Ronin, Shogun, Tanto, Emperor or FX DonnyFl moderator and want to convert it to a QD. This conversion kit will allow you to do so.  Features: Indexed so it locks on at same position every time Made of 7075 aluminum Grey anodized Includes barrel/shroud adapter and rear cap Select the barrel thread specific to your airgun

This muzzle brake or air stripper attaches to the front of any air rifle equipped with a DonnyFL Quick Disconnect Adapter. Features: Made of aluminum 6061 T6 Black anodize Weights 2.9 oz Comes with M58 Air Stripper Insert Kit.

These adapters are for the RAW HM 1000x shrouds that are 2inches in diameter. Not compatible with the offset ones.  There are two types of shrouds out there, remove the factory short screw on suppressor.  If your shroud looks like the one in the picture below, select A65   If it looks like the shroud below then select A90. Does not have a thread protector. 

This package comes with 4 replacement felt wraps, screen and o-rings for the selected moderator model.

Please note* remove the front cap on your shroud. Measure the outer diameter of the threaded part. If close to 27mm, select this adapter. If not most likely A59 Features: Made of 6061 T6 Aluminum Matte black anodize Compatible up to 50 caliber Includes diamond knurled thread protector

This rear cap will fit Ronins, Emperors and Fat Boys. The ribs gives you a better handle to make removing easier. Please keep in mind with this cap, the suppressor will not fit into the red tubes.  

Ronin is big and bold, and that's how we love him. Maybe a little overkill for the .177 and .22 but it looks so awesome!   Available in .22/2.5, .30, .357 and .50 calibers 1/2 x 20 UNF, Big bore (M18x1), M14x1.25 and FX (M20x1) rear caps available Mono-core design to increase accuracy and limit the chances of pellet clipping No moving parts or epoxy that may become loose after 1000's of rounds Precision CNC'd by professional machinist Sand blasted and anodized for maximum durability Take apart in less than 10 seconds by unscrewing the rear end cap and pushing back the mono-core. No hex key or torch needed when you want to perform maintenance inside the unit. Customizable, you can further dampen the sound by wrapping the interior tube with different sound absorbing materials. Comes pre-wrapped in felt Machined grooves on the outside for easy handling. Weights around 10.4 oz Comes with protective red tube for easy transport and storage. Swap out the rear cap with another thread size. *Note: If you see white lines on the inside of the front cap, that's ok. Those were caused by the prongs holding the pieces while anodizing. They are not pellet clippings. *Airgun use only, will not ship outside of Mexico   *International Customers, please be aware that if you add this to your cart, there will not be an option to ship your items. If you have other items that are non-restricted, they won't show up either until you remove the restricted item from your cart.   *Return Policy