Edgun R3M and R3 Degasser T...
$ 992.00
This tool makes degassing the Edgun R3M and R3 safe and easy. It also acan also be used to pull out the regulator.
Instructions:
before screwing the tool onto the Edgun, back out the screw a little to allow the valve pin to go into the tool.
screw the tool onto the valve
Using the blue knob slowly screw into valve pin. You'll start to hear a hissing noise and that's the air being released.
once empty, your gauge should be down to zero
to remove the regulator, make sure the gun is completely empty. Unscrew the screws holding the regulator in place.
Once all the screws are out, screw the degasser tool onto the valve and pull it out of the air tube
FX Shroud Thread Protector
$ 221.00
This knurled thread protector will fit FX Impact, FX Crown and Wildcat 1/2 x 20 shrouds.
Features:
6061 T6 Alluminum
Matte black anodize
Kurled
12mm thick
Edgun Leshiy 2 Shroud Kit
$ 1,323.00
This kit is to replace the stock factory shroud and allows you to screw on an airgun suppressor with 1/2 x 20 threads. The shroud is 2 inch in diameter so best to use Ronin/Emperor/Fatboy with it.
Things to keep in mind:
Mechanical noise will still be loud. Nothing we can do to reduce that with our kit. Have someone shoot the gun and take about 10 steps back. You'll get a better feel for the muzzle noise.
The shroud is empty to provide the max air expansion.
The stock will fold but will not lock. you will need to get the extended pin from Edgun West
Available in two sizes 250mm and 350mm
It's ok to use the 350mm shroud on a 250mm barrel (more volume = quieter)
Features:
Made of 6061 T6 Aluminum
Black anodized
1/2 x 20 male threads (does not have a thread protector)
Comes with 2 Stainless Steel screws
Instructions
FX Barrel Adapter For Leshiy 2
$ 418.00
Suppose you have extra FX barrels laying around and you want to use them with your Leshiy 2. This adapter will allow you to attach an FX Airguns native barrel to your rifle.
Remove the FX factory brass transfer port and screw on our adapter. Slide the barrel back in and you're all set to go.
Currently only available for the .22 and .25 & .30 caliber barrels.
Fatboy 2.0 Extension/Extend...
$ 836.00
Need to make the fat boy quieter? You can add this 3 inch extender to capture more air and reduce the muzzle blast some more.
Features:
6061 T6 Aluminum
Black anodize
Matching outer tube design to the fat boy
Also compatible with the Ronin and Emperor
Fatboy 2.0 Muzzle Brake M51
$ 627.00
This muzzle brake or air stripper screws onto the front of the fat boy.
Note: This unit does not come with the individual air strippers. You can change the caliber size by using the inserts that was included with the fat boy.
Features:
Made of aluminum 6061 T6
Black anodize
Weights 2.9 oz
Add the optional 3 inch extender for the fatboy to make it quieter!Extender
Ribbed End Caps For Ronin/E...
$ 772.00
This rear cap will fit Ronins, Emperors and Fat Boys. The ribs gives you a better handle to make removing easier. Please keep in mind with this cap, the suppressor will not fit into the red tubes.
Muzzle Brake Air Stripper I...
$ 551.00
Upgrade kit for your fatboy muzzle brake. Comes with two air strippers for each size.
Note* Not compatible with the gold limited edition muzzle brakes.
Features:
.177/22, .22/25 and .25/30
Bronze anodize
Delrin tool to install air strippers